In 2007 there was a lot of argument about putting RFID tags into Australian passports, and many people were saying we were destined for a future where everyone was implanted with RFID so they could be tracked by the government and large corporations. I wanted to understand the technology and the risks involved, so I did the only logical thing: I implanted an RFID chip in myself!
I’ve shown use of my implanted RFID chip in previous SuperHouseTV episodes, but this is the first time I’ve shown the footage of me actually implanting the chip in myself.
View on YouTube: www.youtube.com/watch?v=Kv_OG7zG7ro
Now that I’ve modified the Lockwood Nexion door lock on my workshop for Arduino control, the next step is to add an RFID reader near the door so that I can scan the RFID chip implanted in my arm to unlock the door.
Note that I deliberately did not go into any detail of the RFID implantation in this episode, so it’s safe to watch even if you don’t want to see me doing home surgery on myself! I’ll cover that in a separate episode so anyone who doesn’t want to see it can avoid it.
Door locks are one of the most useful things to control from your home automation system. Using electronic locks you can give your house central locking just like your car, control them from your phone or via the Internet, or even control them using an RFID tag or implant.
I modified a Lockwood Nexion keyless lock to allow it to be controlled by an Arduino, and linked it to my home automation system.
View on YouTube: www.youtube.com/watch?v=mqEcJO0UafA
“EtherMega” (Arduino Mega with onboard Ethernet) mentioned in the video
Electrical conduit allows you to run cables outside, underground, and in other nasty places. Sometimes though you have to get cable into places that look impossible, such as under an existing concrete path or driveway that you can’t rip up. It’s not as hard as you may think. I used a technique called “water boring” to install a conduit under a concrete footpath in just a few minutes, without having to dig up the path.
View on YouTube: www.youtube.com/watch?v=9rXFU59D1uE
One of the little time-saving tricks I use in my home automation system is setting the Ethernet MAC address automatically on each device. This saves having to set the address manually in the sketch of every device.
I’ve written it up in a tutorial on the Freetronics site:
Setting Arduino Ethernet MAC addresses manually and automatically
I’ve found that the second-hand Ethernet switches I use in my home automation system have annoyingly loud fans, so I modified them to run the fans more slowly and connect to my Arduino-based environmental monitoring system.
Links for this episode:
Discuss this episode in the forum: forum.freetronics.com/viewforum.php?f=30
I’m using Ethernet extensively in my Arduino home automation system for communication with devices distributed around the house, so being able to also provide power to those devices over the same network cable is a big time saver. Until now I’ve been using a “DIY” approach to Power-over-Ethernet (PoE) with midspan injectors sending about 10-12V down the wire, but I’m now converting it all over to use Netgear switches with 802.3af (48V) PoE support built in.
This episode covers some of the options for PoE with Arduino, and demonstrates how you can do it both in a cheap DIY method and using commercial PoE switches.
The automation switchboards in my house have Ethernet interfaces thanks to an EtherTen (just like an Arduino Uno, but with built-in Ethernet and PoE) mounted inside. This episode shows the switchboard internals, including how the EtherTens switch output loads around the house. It also shows the termination of the house network that starts out as a bit of a mess, but is much neater by the end of the video.
Links for this ep:
A basic introduction to the approach I’m taking with linking high-voltage devices in my house to the automation system, and how logical inputs are associated with outputs using MQTT.
Apology: The “threat” I attribute to Andy in the video is not something he’s ever said, or something I’d expect him to say. He’s a peaceful soul, and it was purely hyperbole on my part when I was recording the video!
Links for this ep:
Music credits: the track used in the intro and ending is “Interface” by ElectroLatrine, www.electrolatrine.net. Used with permission.
If you’re just getting into home automation and go searching for Open Source HA projects, you’ll discover there aren’t any obviously dominant players – more a mix of partly-developed personal projects that aren’t very portable. Why is that?
Links for this ep: